LS343 Uplight Luminaire

	L S 3 4 3
	UPLIGHT LUMINAIRE	_( I P 6 8 )

i n g r o u n d

The In-ground Stainless Steel Range incorporates quality and innovation in materials, manufacture and finishes: from robotic fusion welded marine grade 316 stainless steel housings through to the IP68 rating achieved by its dynamic, high temperature silicone cover seal with memory additives.

Built around an innovative modular system, future conversions from one lamp source to another are incredibly simple with internal gear and reflectors simply clipping into place without the need to modify the wiring loom of the fixture.

learn more...

Sources

PureOptics™ (advanced glass reflector offers 99% efficient reflectivity), or aluminum reflector

- MH / HIT / T6 (39, 70watt)
- Available with electronic gear/ballast

- CFL / TC-T (18, 26watt)

- CFL / TC-TEL (18, 26, 32, 42watt)
- Electronic ballast

- HPS / HSE (50, 70, 100watt)

- MV / HME (50, 80watt)

MH PAR30 (100watt max)
39 and 70watt available with electronic gear / ballast

MH PAR38 (100watt max)
39 and 70watt available with electronic gear / ballast

INC PAR30 (100watt max) / PAR20

INC PAR38 (100watt max)

Halospot AR111 (100watt max)

CDM-R111 39watt

Features

Many optical configurations available

Ingress protection rating - IP689
Suitable for wet locations

OptiClear™ max static load - 9200lb (4200kg)
Applied to a 2in (51mm) diameter area in the center of the glass

Corrosion resistant 316 stainless steel - marine grade

Adjustable gimbal
Dependent on selected optical system

Modular design for easy installation and maintenance

Non-galling clinch nuts dramatically reduce cross threading or binding

Moisture control device to reduce misting on glass

Self resetting thermal protection device to protect unit from overheating

Corrosion resistant stainless steel cover fasteners

Options

Electronic gear / ballast for high efficiency and longer lamp life (39, 70watt)

HumanTouch™ total temperature reduction technology

OptiClear™ lens for increased efficiency
High optical transmission, toughened

GripGlass™ slip resistant safety glass

Recessed, round flush and square flush covers

Installation
- Direct burial
- Mounting collar (decks and grates)
- Pre-installation (concrete and drive-over)

Accessories

Accessories: Metal Halide

LS636	Brass Grill	LS690	Prismatic Lens
LS6013	Slatted Louvre	LS6011	Cross Hatch Louvre
LS688	Refractor Lens	LS6014	Cylindrical Louvre
LS6012	Cross Hatch Louvre	LS689	Dichroic Filters
LS691	Prismatic Lens
LS685	Linear Spreader Lens
LS686	Dichroic Filters
LS640-K	Pre-Installation (Concrete)
LS640	Pre-Installation (Decks & Grates)		view accessory diagram...

Installation: Direct Burial

Recessed Cover

For concrete or similar surface, where no lid overhang is desired.

Brass: Polished

Stainless steel 316: Polished

Stainless steel 316: Brushed

(Note: Not suitable for drive over)

Flush cover Plate

For surfaces where the lid has to cover a gap between fitting and surround.

Brass: Polished

Stainless steel 316: Polished

Stainless steel 316: Brushed

(Note: Not suitable for drive over)

Installation: Pre-Installation Kits

Pre-Installation - Decks & Grates

(Add LS640 accessory to the specification for this configuration.)
For hollow floors

Brass: Polished

Brass: Brushed

Stainless steel 316: Polished

Stainless steel 316: Brushed

Pre-Installation - Concrete (Block Out)

(Add LS640-K accessory to the specification for this configuration.)
For drive over. For installation in to concrete or similar surface and for when it may be preferable to install mounting location and cable before installing lamp fixture.

Brass: Polished

Brass: Brushed

Stainless steel 316: Polished

Stainless steel 316: Brushed

PureOptics™ with Adjustable Gimbal